How to crochet out of a grid pattern
How to work a jumper top down
Several of our jumpers are worked top-down, and this is primarily because it provides more flexibility in terms of adjusting the jumper to personal measurements or preferences. It is easier to adjust the length of sleeves, body and especially the yoke. Working top-down also makes it easier to try the piece on while working.
In this lesson we show you how to work a jumper with a simple raglan increase. Start by picking the pattern you want to knit and use this lesson to guide you. If you want to work on a pattern with a different kind of raglan just follow the instructions for increases in you pattern - you’ll notice that the principle of top-down is the same as in this example. Similarly, this technique can also be used when working a round yoke, just follow the increase instructions for the round yoke instead of the raglan showed here.
Additionally, if you’re working a jacket top-down the technique will be the same, but you’ll work the piece back and forth on needle, starting mid front (a marker at the back will not be necessary).
Let's get started
1) We have started this example by casting on 48 stitches and working 3 cm rib (knit 2, purl 2), before starting the raglan increases.
After the rib edge, continue in stocking stitch and place a marker mid-back. Continue by placing 4 marker threads for raglan in the transition between body and sleeves (from 1. mark to 1. marker thread = half back piece. From 1. to 2. marker thread = 1. sleeve. From 2. to 3. marker thread = front piece. From 3. to 4. marker thread = 2. sleeve. The remaining stitches between 4. marker thread and 1. mark = half back piece).
2) Start increasing for raglan on each side of the 4 marker threads.
3) Increase as follows: start 1 stitches before marker thread, make 1 yarn over on right needle.
4) Work 2 stitches (marker thread sits between these stitches), make 1 yarn over on right needle.
5) First increases (yarn overs) before and after 1. marker thread is now complete. Repeat increases at each marker thread (= 8 stitches increased on round).
6) On the next round, knit the yarn overs twisted (work in the back loop of stitch) to avoid holes.
7) Continue with pattern, and increase for raglan as explained.
8) When all increases for raglan are complete, continue working until you reach the measurements for where piece is divided for body and sleeves.
9) Divide piece for sleeves and front / back piece, and finish each part separately. Work until 1. marker thread (= half back piece).
10) Place stitches between 1st and 2nd marker thread on a thread / stitch holder (= 1st sleeve).
11) Cast on new stitches under sleeve.
12) Work stitches between 2nd and 3rd marker thread (= front piece).
13) Place stitches between 3rd and 4th marker thread on a thread / stitch holder (= 2nd sleeve).
14) Cast on new stitches under sleeve (same number of stitches as cast on under 1. sleeve).
15) Work remaining stitches on back piece (until 1. marker).
16) Work the body in the round, follow instructions for increases, decreases, length and rib edge in your pattern. If you're unsure about the length of piece, or considering shortening / lengthening it, you can easily try the jumper on while working (TIP: when trying the piece on, distribute stitches over several circular needles to minimize the risk of losing any stitches ).
17) Work sleeves: place stitches from one of the threads / stitch holders back on the needle.
18) Cast on new stitches under sleeve, see picture A) or pick up 1 stitch in each stitch of the stitches cast on under the sleeve, see picture B) - see pattern for exact number and place a marker. The piece is now measured from here.
19) Work the length stated in the pattern, place a new marker in the middle of the new stitches cast on. Decrease 1 stitch on each side of the marker.
20) Work until 2 stitches remain before the stitch with marker, slip 1 stitch onto right needle, knit 1, pass the slipped stitch over (= 1 stitch decreased).
21) Work stitch with marker.
22) Knit 2 stitches together (= 1 stitch decreased).
You have now decreased 1 stitch before and 1 stitch after marker (= 2 stitches decreased).
23) Follow instructions in pattern regarding the number of decreases and cm / rounds in-between each decrease.
24) When both sleeves have been completed, sew the hole under sleeves.
When the body and sleeves are completed according to the pattern, remove all markers and marker threads, and fasten all strands. The jumper is now finished!
Still haven't chosen a top down pattern? Find some inspiration below:
- What happened between Magwitch and Compeyson Dickensian
- Bean hull candles wholesale fragrance
- How much money is a sixpence worth
- Who wins president polls
- Who can you kiss during Ramadan
- How does the redback spider antidote work
- What does cdc stand for in slang?
- Ezhuthachan Community in Kerala where Gandhi did
- Howard Samuel Norman Attorney General Philippines
- Netflix when Marie was there
- Brian Howard Rhode Island Obit
- What is 671b Criminal Code
- How to wash clothes without water
- How many clicks on a Norditropin pen
- How to add an account in the hdfc bank
- How to create yahoo pipes examples
- Who Owns Southwick Estate Hampshire
- What does thank you mean for humouring me
- How to use diaion hp 20 resin
- JAR file from WhatsApp Web
- Battlestations Pacific, how to unlock the Kikka
- Phimocure instructions for playing
- Hable con ella soundtrack descargar whatsapp
- What is a Gimmel bottle
- Puristic group, how to join
- Setting sprays in tf2 how to tinker
- Who plays david obrien pretty little liars
- Mepz 40 mg corresponds to how many ml
- Which 3 factors influence the potential energy
- Velvety fur mh3rd how to get Drachenite
- Esl How To Write Better Business Email
- Doctor shielding the nut home
- How to set up the swann mydvr software