How to identify ykk zipper

Thread the zipper back in - DIY instructions

A zipper that has been stripped out is a tricky business. The sliders must be threaded in a specific way to function properly and not to get caught within a few seconds. Threading in a zipper is necessary if the previous slide is jammed or broken. In this case, the exchange is worthwhile, which can be carried out without any problems with the appropriate instructions.

Content

Thread in the zip zipper

Threading a zipper is not an easy job. The component made of metal or plastic is required to close and secure the zipper so that it does not yield even when it is moved and under high pressure. It can happen that over the course of using the Zip zipper must be replaced if it no longer moves, is completely bent or broken.

Here comes this Threading for use, a work step that requires a certain amount of tact. If you're looking for a detailed DIY guide to threading the slider, you've come to the right place. This explains the processes for successfully pulling up the new sled.

Materials and tools

If you got on a broken or zipped off Zipper you don't need to despair or take your garment straight to a tailoring shop. If only the Zip zipper needs to be replaced, it is easy to thread it by yourself and then use it again.

To do this, all you need is the right utensils:

  • Flat nose pliers
  • new zipper (also known as a slider or slide)
  • needle
  • Sewing thread
  • Zipper clip (if this is also damaged)

When choosing a new zipper, pay attention to the material. True are Slider out plastic significantly cheaper and are often offered in large quantities at low prices, but they are not really robust and break quickly. Metal slide Only sometimes bend over time, but almost never break. They withstand large forces much better and need to be replaced less often.

If you do not have flat-nose pliers, you can choose other smaller pliers as long as they do not have a sharp cutting edge. You want the new one Zip zipper Do not damage immediately when threading. When choosing the yarn, you have to look at which type has been used so far and get the same accordingly.

Tip: When you order a new zipper, you should opt for metal products from YKK and OPTI. These are the largest manufacturers of zippers on the market and are known for their high-quality, durable zipper pullers.

preparation

Before you get the new Thread the slide, you need to remove the old one. If this has not broken off or has resolved itself, you have to take care of it yourself.

Proceed as follows:

1. Most of the zippers are attached using a clip located at the end of the zipper. Take the pliers in your hand and press the wings of the clip apart so that you can remove them.

Do not pull on the clamp as this may damage the fabric. if the Bracket is not broken or broken, you can continue to use it. Otherwise it has to be replaced so that the slide does not simply slide down again.

2. It is also possible to use a zipper thick seam to fix.

If this is the case, you have to open them with a seam ripper. To do this, simply guide the seam ripper under the seam and separate the seams.

3. Once the staple or suture is removed, pull the Zip zipper just go down.

If the zipper gets stuck, it is bent open with the pliers and can then be removed.

4. Finally, you should use the zipper again for bent teeth or something similar check. It may be necessary to replace the entire zipper, which will save you work. So check it as thoroughly as possible.

On many jackets, skirts or some dresses, the zippers are not completely closed on either side. The zipper zippers, on the other hand, have a so-called End stopper understand. This is located directly in the slide and prevents accidental loss of the zipper.

When it comes to such a slider, all you have to do is open it or use the pliers to bend it around the End stopper to to solve. Then you can remove the part and thread it in the same way as described in the DIY guide below.

Threading the zipper: DIY instructions

With the right DIY instructions, it is easy to thread the zipper and thus again within a few moments working close. Here you will find detailed DIY instructions for threading the zipper zipper, which will make it easier to change the zipper. This is suitable for both types of slide, with or without an end stop.

The instructions in detail:

1. To begin with, check the new one Zip zipper for possible damage. Sometimes it can happen that these come out of production incorrectly. If the sled is OK, you can use it and don't have to worry that it will be damaged in the coming uses.

2. It is always threaded from first rightas this is the longer side of the zipper. The left side is rarely used as the leading. Therefore, see which of the two is longer than the other. You thread the over this Zip zipper then a. With some zippers, this can be seen through the box part, a square end piece on one of the two sides, which is clearly visible.

3. Take the zipper puller in your hand and adjust it so that the handle is facing up. The thinner end of the zipper must look towards the end of the zipper. Now thread the leading side into the slide. This actually works the same way that you close your jacket.

4. After the first side has been threaded, the second follows.

Proceed in the same way here, just bend it a little to make it easier to thread. After this threaded on both sides bend them down slightly so that the slide does not accidentally come off again.

Now carefully close the zipper and leave it in the closed position.

5. Finally, attach the Bracket again in the same place with the help of the pliers. To do this, press the ends of the clamps through the fabric and bend them. Nothing more is required to complete this variant.

6. For zippers with a Sew the seam You the end.

Take the yarn by hand, thread a good length into the needle and close it with a knot.

Now sew several layers directly to each other at the point where you previously loosened the seam to create one Stop mechanism to enable.

Once this is thick enough, you can finish the project.